Ice Epoxy RSE - fast setting transparent epoxy resin
ICE RSE is a normal and low temperature curing epoxy resin adhesive. This epoxy resin is easy to use because it is fast curing, has a strong tack and can be heated at 55C ready in 5min.
The low colour and low viscosity allow for bubble-free, crystal clear epoxy repairs, ideal for art and hobby applications. The product is in the gel state for a short time. ICE-RSE has a low VOC content, ensuring user safety and reducing environmental impact.
Main uses
Ice RSE epoxy resin is used for
- specially designed for the installation of electronic components
- for bonding metals
- for bundling electronic products
- for binding wood
- for bonding hard materials
- for infusion of forms
- for the isolation of other electronic components
- for moisture-proof installation
- for confidential cover
- etc.
TECHNICAL and MANUFACTURING characteristics
- COLOUR - clear
- MIXING RATIO, BY VOLUME - 1:1 (RESIN: HARDENER)
- MIXING RATIO, BY WEIGHT - 1:1 (RESIN: HARDENER)
- PRODUCT VISCOSITY 25 °C JUURES - component A 8000-1200 CPS; component B 5500-8500 CPS
- WORKING TIME - 10 minutes at 25 °C
- INITIAL CURING TIME (CURABLE) - 1 hour at 25 °C; 5 min at 55 °C (2g product)
- RECOMMENDED FULL CURE TIME - 1 hour.
- IDEAL OPERATING TEMPERATURE - optimum 25 °C
- THERMAL CONDUCTIVITY - 0.56 W/M.K
- POWER LOSS - 0.42 1KHZ
- COMPRESSION TENSITY - 11.4 kg/mm2
- HARDNESS, SHORE D - 82
IMPORTANT REMARKS
- The cost shown is calculated for a flat surface. A porous or imperfect surface will require more material for the same material cost.
- The viscosity shown applies only to a transparent product. The addition of any dye may affect the viscosity.
MANUAL
In a dry, clean container, mix 1 part resin to 1 part hardener. Stir thoroughly along the inside wall of the container and then allow to stand for 3-5 minutes. Adjust the amount of epoxy according to the working time and dose to avoid wastage. If the relative humidity is above 85%, the solidified product surface will easily absorb moisture from the air, forming a white mist. Therefore, if the relative humidity is above 85%, it is not suitable for curing at room temperature. It is recommended to use the heating method for solidification. If it is necessary to cast in a cool room, it must be left in the mould for at least 3 days to cure completely.
CLEANING
Clean all tools with acetone. Once the product has hardened, it can only be removed by sanding. It is recommended to clean immediately after use.
RANGES
ICETHIN should be stored in a dry, shady place at 10-15°C and out of the reach of children. Do not leave the resin or hardener in an open container. It should be used in locations where the humidity is below 60% and the temperature is between 19-23 °C. Use a dehumidifier if necessary. ICETHIN should be used within one year of purchase.
HEALTH AND SAFETY
Wash with soap and water if it comes into contact with skin. In case of contact with eyes, rinse immediately with water for at least 15 minutes. Consult a doctor. In case of respiratory problems, remove to fresh air. Remove contaminated clothing and clean before reuse. Components A and B contain toxic ingredients. Prolonged skin contact with this product may cause irritation. Avoid contact with eyes. Exposure may cause severe burns. Avoid inhalation of vapours from this product. This product is a strong sensitizer. Wear protective goggles and chemical resistant gloves. The use of a respirator filtering organic vapours is recommended. Use suitable ventilation. *Please refer to the Material Safety Data Sheet for further information.
IMPORTANT NOTE
All claims, recommendations and technical information contained in this document are accurate to the best of ICE EPOXY's knowledge. The information relates only to the specific material referred to herein. It may not apply when used with other materials. It is the responsibility of the user to verify the suitability of this information for the specific application and to test the product prior to use. ICE EPOXY accepts no legal liability for the use of this information. ICE EPOXY assumes no legal liability for any direct, indirect, consequential, economic or other damages, other than product replacement.